Fedora 18 nVidia Drivers Install / Uninstall Guide - Comment Page: 2

Looking Fedora 22/21 nVidia Drivers Install Guide? [inttf_post_ad1] This is guide, howto install nVidia proprietary drivers on Fedora 18 "Spherical Cow" and disable Nouveau driver. This guide works with GeForce 8/9/200/300/400/500 series cards (and currently also with GeForce 6/7). Later you might need different version of nVidia drivers if you use GeForce 6/7 card. Fedora 18 nVidia driver installation is not much different from previous Fedora versions. I have tested this guide with a couple computers, so let me know, if you have some problems. 1. Before nVidia drivers installation 1.1 Check is your nVidia card supported lspci |grep -i VGA ## Example output...

74 comments on “Fedora 18 nVidia Drivers Install / Uninstall Guide - Comment Page: 2

1 2
    1. Have a problem with latest kernel 3.8.3-203. When starting X (startx) screen goes blank and system freezes. Have not done any in-depth analysis on it. Just rebooted and started with previous kernel 3.8.3-201 which works fine. Eviro is:

      HP Pavilion d4890y w/ RAID1
      kernel-PAE-3.8.3-201.fc18.i686
      kmod-nvidia-3.8.3-201.fc18.i686.PAE-304.64-7.fc18.2.i686
      akmod-nvidia-304.64-7.fc18.i686
      xorg-x11-drv-nvidia-libs-304.64-5.fc18.i686
      NVIDIA Corporation G80 [GeForce 8800 GTS] (rev a2)

      Reply
      • Hi patrick,

        Could you try is it working with latest 3.8.4-202 kernel?

        Reply
        • I’d try if I could but I don’t have it available… I’m just waiting on the next kernel release and hoping that it will magically fix.

          Reply
          • OK I had a chance to do a little testing and confirm. Here’s the results:

            kernel-3.8.4-202 -> works
            kernel-3.8.3-203 -> does not work as described above
            kernel-3.8.4-201 -> works

            Reply
            • Thanks for testing. This is strange and interesting, but best news is that the it works with kernel-3.8.4-202. :)

              Reply
    2. Brilliant instructions, just works fine.

      My experience so far…(in case if it is going to be useful for someone)

      HP xw6200 Workstation
      Nvidia Quadro 450
      3 monitors

      Linux kernel : 3.8.3-203.fc18.x86_64
      Went for akmod option

      Had issues with Gnome desktop. Hence, switched to KDE Spin that is just fine.

      While configuring 3 monitors:
      1. Configured the first 2 monitors with ‘TwinView’ with monitor-1 being primary, absolute and monitor-2 positioned ‘right of’ monitor-1.
      2. Configured monitor-3 as ‘Separate X screen’
      3. Enabled ‘Xinerama’
      4. Resolution left to ‘Auto’

      Not sure, if the above is the best way of configuring 3 monitors. But it works just fine except that the first 2 monitors are treated as a ‘display’ seeamlessly. (i.e., if I maximize any window, it spreads across both monitors)

      Reply
      • Hi Murali,

        Thanks for posting your experience and this 3 monitors configuration. For me it’s looks very nice way to configure it. I normally use only 2 monitors. :)

        Reply
    3. Without a doubt Fedora is the best Linux distro I’ve ever experienced. The instructions for installing the nvidia driver worked like a charm!

      Reply
    4. I seem to be struggling to get my Asus G75VW-AH71 laptop to use the nvidia driver.
      I have followed the above instructions and it boots to a certain point and then stops.
      If I hit escape to watch the boot process the last thing I see is:
      OK – Started GNOME Display Manager
      OK – Started Builds and install new kmods from akmod packages

      Nothing shows after that. I can ctrl/alt f2 to get to a terminal screen and login as root

      The Asus has a Nvidia GTX 660M. Doesn’t appear to be using any optimus.
      lspci shows:
      01:00.0 VGA compatible controller: NVIDIA Corporation Device 0fd4 (rev a1)

      Kernel/nvidia info:
      Linux localhost.localdomain 3.8.4-202.fc18.x86_64 #1 SMP Thu Mar 21 17:02:20 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux

      akmod-nvidia-304.64-7.fc18.x86_64
      kmod-nvidia-3.8.4-202.fc18.x86_64-304.64-7.fc18.x86_64
      nvidia-settings-1.0-26.fc18.x86_64
      nvidia-xconfig-1.0-25.fc18.x86_64
      xorg-x11-drv-nvidia-304.64-5.fc18.x86_64
      xorg-x11-drv-nvidia-libs-304.64-5.fc18.x86_64

      lsmod | grep -e nouv -e nvidia returns nothing so I’m guessing the nvidia is not loaded.

      What can I try next?

      Reply
      • Hi Mark,

        Everything looks good, but yes nvidia driver is not loaded, you can try following on command line (as root):

        
        modprobe nvidia
        

        Do you get some error? If not then check following output again:

        
        lsmod | grep -e nouv -e nvidia
        
        Reply
        • JR, figured it out. I had left secure boot mode enabled in bios/uefi on my Asus. Turned it off and nvidia loaded.

          Only other odd thing I have seen is when I make any changes to grub2 via grub2-mkconfig it breaks nvidia. I then have to:
          yum remove xorg-x11-drv-nvidia\* nvidia-settings nvidia-xconfig
          reboot
          yum install akmod-nvidia xorg-x11-drv-nvidia-libs

          to get it working again. Luckily I don’t make changes to grub2 often.
          Thank you for your help in this forum.
          Mark

          Reply
          • Hi Mark,

            You are welcome and nice to hear that you got it working.

            If you want me to check that grub2-mkconfig problem, then I need more information what changes you do/did? And maybe grub2 config before and after grub2-mkconfig command. :)

            Reply
    5. De lo más útil este sitio. Muchisimas gracias. :D

      Reply
    6. This totally screwd up my laptop.i follow the tutorial to the letter.
      I have acer aspire with nvidia GT480 .
      The error from the xorg log was :
      fatal error cannot find device.
      And cannot find monitor .
      I tried with the kmod and akmod .
      I updated the whole system with the kernel .
      Any ideas ?

      Reply
    7. Sorry i meant GT540 in this laptop.

      Reply
      • Hi odysiuss,

        Could you post output of following commands:

        
        lspci |grep -i VGA
        
        uname -a
         
        lsmod |grep -e nouv -e nvidia
         
        rpm -qa \*nvidia\* kenrel\* |sort
        
        Reply
        • hi JR

          i was followed your instruction about installing nvidia driver
          it’s work, just fine, but when i look on lspci | grep VGA
          i got this message

          NVIDIA Corporation Device 0dec (rev a1)

          why this can’t change to Geforce GT525

          specification
          core i7
          ram 8gb
          nvidia geforce GT525

          thanks a lot

          sorry my english is bad

          Reply
    8. Hi JR.. Thanks for the tutorial very clear and organized… :D
      Sry about this but I’ve started use fedora this week…
      I have some problems installing the nvidia driver of GT 650M…
      I follow the steps but when I rebooted the screen frezzed…
      I tried to start by startx and get screen not found..
      Could you give me some advices..
      I have already checked:

      lspci |grep -i VGA
      lsmod | grep -e nouv -e nvidia

      The lsmod pointed out 3 modules…
      and the lspci list my VGA as compatible..

      Thx

      Reply
    9. Hey is this guide also functioning for mobile version of a geforce – card (610m) ?

      Reply
      • Hi Luis Klar,

        Yes this should work with Geforce 610m card too.

        Reply
    10. Hello,

      your commands works perfectly, But after follwing this tutorial I get an error :
      error [105] err:d3d_caps:WineD3D_CreateFakeGLContext Can’t find a suitable iPixelFormat.
      And it seems this broke the wine game settings (such as WoW or Lotro ).
      I’ve found the solution and it’s to execute :

      yum install xorg-x11-drv-nvidia-libs.i686

      then everything works fine and my fps rate is just amazing unsign this new nvidia driver.

      thanks.

      Reply
    11. I’ve tried this tutorial on Fedora 18… after a reboot graphics doesn’t start anymore.
      If you have the same problem you can do this:
      boot Fedora, also if boots only a first part, and then press ctrl+alt+F2
      now you should open a shell, ok remove packets with:
      sudo yum remove packets-name
      example:
      sudo yum remove akmod-nvidia xorg-x11-drv-nvidia-libs

      reboot. Unfortunately the graphics starts, but with the incorrect resolution and at the moment I can’t change this resolution :(

      Reply
      • Ok, I’ve found a solution! I’ve boot with a previus kernel version and I uninstalled and then reinstalled the last kernel version, so now I’ve the right resolution of the screen :)

        Reply
    12. I just wanted to comment on the Nvidia uninstall / re-enabling of nouveau. Simply removing the Nvidia drivers leaves the nouveau driver disabled in Grub, so, you’re left with only the Visa driver or worse. The trick to repair this is, after removing the Nvidia driver, reboot and….

      yum remove kernel
      yum install kernel
      (yum reinstall kernel…?)
      shutdown -r now

      Since the Nvidia drivers are gone when your box comes back up the latest kernel will be re-installed with a nouveau configuration proper. Of course your procedure will vary depending on if you’re using a non-default kernel.

      Reply
    13. Hi

      I have a Nvidia Geforce 9500 GT installed in a machine running CentOS 6.5.

      Output of # lspci | grep VGA:

      01:00.0 VGA compatible controller: NVIDIA Corporation G96 [GeForce 9500 GT] (rev a1)

      Does not give me any HDMI audio devices listed.

      Output of # lsmod | grep nvidia

      nvidia 10681847 40
      nvidiafb 42032 0
      fb_ddc 1631 1 nvidiafb
      i2c_algo_bit 5935 1 nvidiafb
      vgastate 9157 1 nvidiafb
      i2c_core 31084 5 i2c_i801,nvidia,nvidiafb,fb_ddc,i2c_algo_bit

      No HDMI audio devices show up but the default sound card is available.

      The TV works with HDMI audio. I do not know if the machine has ever output audio through HDMI previously, but I think so. It used to be running Windows Server 2008.

      Don’t know what else to try now.

      Reply
1 2

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Close