Fedora 35/34/33 NVIDIA [495.xx / 470.xx / 390.xx / 340.xx] Drivers Install Guide - Comment Page: 113

This is guide, howto install NVIDIA proprietary drivers (manually using .run files) on Fedora 35/34/33/32/31 and disable Nouveau driver. This guide works with GeForce 8/9/200/300/400/500/600/700/800/900/10/20/30 series cards. GeForce RTX 30 series cards works with 495.xx, 470.xx, 465.xx and 460.xx NVIDIA drivers, (RTX 3090, RTX 3080 and RTX 3070, RTX 3060, RTX 3060 Ti) GeForce RTX 20 series cards works with 495.xx, 470.xx, 465.xx, 460.xx and 450.xx NVIDIA drivers (RTX 2080 Ti, RTX 2080, RTX 2070 Ti, RTX 2070, RTX 2060) GeForce GT/GTX 600/700/800/900/10 series cards works with 495.xx, 470.xx, 465.xx, 460.xx, 450.xx and 390.xx NVIDIA drivers (GTX 1080 Ti, GTX 1080, GTX 1070, GTX...

3,067 comments on “Fedora 35/34/33 NVIDIA [495.xx / 470.xx / 390.xx / 340.xx] Drivers Install Guide - Comment Page: 113

1 111 112 113 114 115 120
    1. Thanks a lot for a great guide!!! It took me around 1h:30min to finish it without previous knowledge.
      Here are the outputs of the commands you asked for.

      (base) [[email protected] ~]$ nvidia-installer -v |grep version
      nvidia-installer: version 340.108 ([email protected])

      (base) [[email protected] ~]$ uname -a
      Linux localhost-live 5.9.15-200.fc33.x86_64 #1 SMP Wed Dec 16 19:14:35 UTC 2020 x86_64 x86_64 x86_64 GNU/Linux

      (base) [[email protected] ~]$ lspci |grep -E “VGA|3D”
      01:00.0 VGA compatible controller: NVIDIA Corporation GT216GLM [Quadro FX 880M] (rev a2)

      P.S.
      If you are using laptop connected to monitor, before you go to system LVL 3, it is smart to turn off monitor and just use laptop built-in display. I got a bit confused during this part, but once I turned off the monitor, restarted the laptop and used only a built-in display everything worked perfectly.

      Reply
      • Hello Nash,

        Nice to hear that you got everything working! And excellent tip to turn off external monitor when booting runlevel 3.

        Reply
    2. Whenever I try booting right now I get two errors for a Nvidia kernel module missing and then it stops at Failed to start Light Display Manager [Nvidia Geforce 560ti, driver version 390.138]

      Reply
      • Hello Phalen,

        Do you have secure boot enabled on BIOS/UEFI? Did you have problems when you run NVIDIA installer?

        Reply
    3. Hi All.

      If you need it (like I did), I patched the 340.108 drivers to compile on the 5.10 kernel.

      Download the package I built for my needs here:

      https://vcloud.voipster.org/index.php/s/nvidia-340-drivers

      You can also download the .patch file there, if you want to do it yourself.

      Good lock! Have fun! :)

      Cheers,

      Andrew

      Reply
    4. I cannot see none of the plymouth theme.
      Before the login screen I only see tree square, initially gray, and after the became all orange.

      Reply
      • Hi Michele,

        Do you have working installation? I mean NVIDIA Drivers works normally?

        Reply
    5. Success. Thank you.

      [[email protected] ~]$ nvidia-installer -v |grep version
      nvidia-installer: version 340.108 ([email protected])
      [[email protected] ~]$ uname -a
      Linux localhost.localdomain 5.9.16-200.fc33.x86_64 #1 SMP Mon Dec 21 14:08:22 UTC 2020 x86_64 x86_64 x86_64 GNU/Linux
      [[email protected] ~]$ lspci | grep -E “VGA|3D”
      01:00.0 VGA compatible controller: NVIDIA Corporation GT218 [GeForce 210] (rev a2)

      Reply
    6. Thanks for the guide, rpmfusion drivers broke my system :D Playing videos in Firefox slowed down the whole system with alot of framedrops and choppy playback. Removed them, installed nvidia driver following your guide, rebooted, smooth as f*ck :)

      Reply
      • Hello dan,

        You’re welcome, nice to hear that you got NVIDIA drivers installed and running smoothly!

        Reply
    7. Just for information purposes, the nvidia driver 390.141 released on Thursday the 7th seems to work just fine without patching on 5.9 kernels

      Reply
      • Thanks Bob,

        I missed this release totally. Works with kernel 5.10.4 too without patching! I update this guide and remove 390xx from NVIDIA patcher script (until 390.141 works)!

        Reply
    8. Dear JR, Many thanks. The new 390.141 driver (no patch!) worked like a charm for the new 5.10.6 kernel and everything is up to speed.
      You are my life saver.

      lspci | g VGA shows
      01:00.0 VGA compatible controller: NVIDIA Corporation GF116 [GeForce GTX 550 Ti] (rev a1)

      — Peter

      Reply
    9. I tried with gt 530 and the 390. It didnt work at first. Something about a make config.
      I did make oldconfig in the kernel source folder and it worked after that.

      Never using nvidia again

      Reply
    10. Hi JR,

      Thank you very much for this. I had fedora version 5.8.18-300.fc33.x86_64 with the Nvidia version 340.108 for the GT215M [GeForce GTS 360M]. This is working!

      When I updated Fedora to the versions 5.9.10 and 5.9.11, I could not boot Linux anymore. Luckily I had kept version 5.8.18 so I could still work on my laptop, but now I can use version 5.9.11

      But Thanks again!

      Reply
    11. I would have never figured all this out alone. You’re a bloody genius. Thank God you published this guide. Brilliant!

      Reply
    12. I have a fresh Fedora Workstation 33 install I just did on my laptop. It has a GeForce RTX 2060 Mobile card.

      [[email protected] ~]$ lspci | grep -E “VGA|3D”
      00:02.0 VGA compatible controller: Intel Corporation UHD Graphics (rev 05)
      01:00.0 VGA compatible controller: NVIDIA Corporation TU106M [GeForce RTX 2060 Mobile] (rev a1)

      I followed the guide, installing the 460 driver. After switching back to Runlevel 5 and rebooting, Fedora won’t start. I see the boot screen with the spinner, but I never get a graphical login screen. The spinner just stops spinning and disappears, but it still just displays the booting screen. I’m able to boot into graphical mode in the kernel which was installed when I installed Fedora, but not in the most recent kernel which was placed on the system when I ran “dnf upgrade” after installing Fedora.

      Reply
      • Hello CS,

        Do you mean that you have fully working desktop with NVIDIA drivers when you use older kernel?

        You can always boot again to runlevel 3 using newest kernel and reinstall 460 drivers. Do you get any errors when you run installer?

        Real problem might be your laptop panel + NVIDIA Optimus technology. Check this for more info: http://download.nvidia.com/XFree86/Linux-x86_64/460.32.03/README/optimus.html

        NVIDIA Drivers installs and works, but you can’t use your laptop panel. One possible solution is check BIOS/UEFI and try to disable integrated graphics or disable NVIDIA Optimus technology.

        Reply
    13. I have NVIDIA Sever Setting no How do I install … ???

      Reply
    14. Merci beaucoup!
      [[email protected] ~]# uname -a
      Linux santorin 5.10.9-201.fc33.x86_64 #1 SMP Wed Jan 20 16:56:23 UTC 2021 x86_64 x86_64 x86_64 GNU/Linux
      [[email protected] ~]# lspci|grep -E ‘VGA|3D’
      02:00.0 VGA compatible controller: NVIDIA Corporation GT216 [GeForce GT 220] (rev a2)
      [[email protected] ~]#

      Is-it possible to do update (dnf update) without problem??
      Merci encore

      Reply
      • Hello cat,

        Yes you can use dnf update without probelems. DKMS should rebuild your NVIDIA kernel modules when you update kernel.

        Reply
    15. This is the single most useful page on the internet, it is informative, accurate, it works and is regularly updated. I have used this page for a long time now. Thanks

      Reply
1 111 112 113 114 115 120

Leave a Reply to Rodrigo Hashimoto Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Close