Fedora 35/34/33 NVIDIA [495.44 / 470.86 / 390.144 / 340.108] Drivers Install Guide - Comment Page: 119

This is guide, howto install NVIDIA proprietary drivers (manually using .run files) on Fedora 35/34/33/32/31 and disable Nouveau driver. This guide works with GeForce 8/9/200/300/400/500/600/700/800/900/10/20/30 series cards. GeForce RTX 30 series cards works with 495.xx, 470.xx, 465.xx and 460.xx NVIDIA drivers, (RTX 3090, RTX 3080 and RTX 3070, RTX 3060, RTX 3060 Ti) GeForce RTX 20 series cards works with 495.xx, 470.xx, 465.xx, 460.xx and 450.xx NVIDIA drivers (RTX 2080 Ti, RTX 2080, RTX 2070 Ti, RTX 2070, RTX 2060) GeForce GT/GTX 600/700/800/900/10 series cards works with 495.xx, 470.xx, 465.xx, 460.xx, 450.xx and 390.xx NVIDIA drivers (GTX 1080 Ti, GTX 1080, GTX 1070, GTX...

3,085 comments on “Fedora 35/34/33 NVIDIA [495.44 / 470.86 / 390.144 / 340.108] Drivers Install Guide - Comment Page: 119

1 117 118 119 120
    1. Hi JR,
      Did the following
      1. Verify nvidia card is supported
      01:00.0 VGA compatible controller: NVIDIA Corporation G72 [GeForce 7300 LE] (rev a1)
      2. downloaded the associated nvidia driver
      NVIDIA-Linux-x86_64-304.137.run
      3. followed the instructions and got the following error when running the nvidia installer:
      make -C /usr/src/kernels/5.13.13-200.fc34.x86_64/tools/build CFLAGS= LDFLAGS= /usr/src/kernels/5.13.13-200.fc34.x86_64/tools/objtool/fixdep
      make -C /usr/src/kernels/5.13.13-200.fc34.x86_64/tools/lib/subcmd/ OUTPUT=/usr/src/kernels/5.13.13-200.fc34.x86_64/tools/objtool/
      make -C /usr/src/kernels/5.13.13-200.fc34.x86_64/tools/build CFLAGS= LDFLAGS= /usr/src/kernels/5.13.13-200.fc34.x86_64/tools/objtool/fixdep
      make[4]: *** [Makefile:55: /usr/src/kernels/5.13.13-200.fc34.x86_64/tools/objtool/objtool-in.o] Error 1
      make[3]: *** [Makefile:69: objtool] Error 2
      make[2]: *** [Makefile:1990: tools/objtool] Error 2
      NVIDIA: left KBUILD.
      nvidia.ko failed to build!
      make[1]: *** [Makefile:261: module] Error 1
      make: *** [makefile:59: module] Error 2

      5. I am running : Linux fedora 5.13.13-200.fc34.x86_64

      Any suggestions on what went wrong??

      Reply
      • Hello Herb,

        Unfortunately NVIDIA 304.xx is not supported anymore with latest 5.13 kernels.

        Reply
    2. Thank you very much! Worked like a charm:

      $ nvidia-installer -v |grep version
      nvidia-installer: version 470.63.01

      $ uname -a
      Linux fedora 5.13.13-200.fc34.x86_64 #1 SMP Thu Aug 26 17:06:39 UTC 2021 x86_64 x86_64 x86_64 GNU/Linux

      $ lspci |grep -E “VGA|3D”
      01:00.0 VGA compatible controller: NVIDIA Corporation GM206 [GeForce GTX 950] (rev a1)

      Reply
    3. Hi there,

      after the installation only my external monitor is working. The laptop monitor does not show anything. How to enable dual monitor?

      Reply
      • Hi,

        Actually this is how to NVIDIA drivers works with NVIDIA Optimus laptops. If you check step 1.2 you can see link to https://download.nvidia.com/XFree86/Linux-x86_64/470.63.01/README/optimus.html

        “The driver may be installed normally on Optimus systems, but the NVIDIA X driver and the NVIDIA OpenGL driver may not be able to display to the laptop’s internal display panel unless a means to connect the panel to the NVIDIA GPU (for example, a hardware multiplexer, or “mux”, often controllable by a BIOS setting) is available. On systems without a mux, the NVIDIA GPU can still be useful for offscreen rendering, PRIME render offload, running CUDA applications, and other uses that don’t require driving a display.”

        Next thing to do is check your BIOS / UEFI. Is it possible to disable integrated graphics / NVIDIA Optimus?

        Reply
    4. Worked like a charm. Thank you very much!

      Reply
    5. Thank you very much.

      nvidia-installer -v |grep version
      nvidia-installer: version 470.63.01

      uname -a
      Linux fedora 5.13.13-200.fc34.x86_64 #1 SMP Thu Aug 26 17:06:39 UTC 2021 x86_64 x86_64 x86_64 GNU/Linux

      lspci |grep -E “VGA|3D”
      01:00.0 VGA compatible controller: NVIDIA Corporation GP107 [GeForce GTX 1050 Ti] (rev a1)

      Reply
    6. Here’s a question:

      How do you go from a NVIDIA GTX1060 to an AMD 5600XT in Fedora 34? What are the exact steps to configure the 5600XT for open source drivers?

      Reply
      • And in case it wasn’t obvious, the GTX1060 is running NVIDIA proprietary drivers installed via your guide.

        Reply
    7. nvidia-installer: version 470.63.01
      Linux asus 5.13.16-200.fc34.x86_64 #1 SMP Mon Sep 13 12:39:36 UTC 2021 x86_64 x86_64 x86_64 GNU/Linux
      00:02.0 VGA compatible controller: Intel Corporation 4th Gen Core Processor Integrated Graphics Controller (rev 06)
      01:00.0 3D controller: NVIDIA Corporation GM107M [GeForce GTX 860M] (rev a2)

      I managed to install it in Fedora34! The only side effect is the system switched to X11 and I lost gests.

      Reply
    8. Thanks a lot ,
      works great !

      Thumbs up for this Guide

      Reply
    9. Hi JR, The recent 5.14.9 kernel did not work for runlevel 5, so I tried, in runlevel 3, executing your steps 2.6.1 — 2.6.5 and re-running NVIDIA-Linux…390.144.run. It failed for the DKMS step. So I will keep with the 5.13.19 kernel (which works fine) and await further news from you. My VGA is NVIDIA’s GF116 [GeForce GTX 550 Ti].

      Thank you for your great instructions! I can’t believe how you actually read 3,040 comments.

      Reply
    10. Black screen after reboot

      Have a Quadro T2000, running fedora34 latested patched, download the latest from nvidia

      Followed all your steps but after a reboot all I get is a blank screen.

      Reply
      • Hello Daniel,

        Could you post output of following commands:

        uname -a
        
        lspci |grep -E "VGA|3D"

        Do you post install full name what you used?

        Reply
    11. THis works with External Monitor plug’in HDMI on a laptop with nvidia GTX 1650 card?

      Reply
      • Hello Adson,

        Yes, it should work with external monitor even if your laptop panel won’t work. You can always restore nouveau if you have problems.

        Reply
      • Hi Bob,

        I’m looking problems with NVIDIA 390.xx. NVIDIA 340.xx is already patched for kernel 5.14.

        Reply
        • I serious do not mind waiting and just using the previous 5.13 kernel for now.

          You do such a great job of getting patches out quickly. (unlike rpmfusion where I can say factually its taken 6 months in the past.)

          Like Peter Scott said, thanks to everyone for a great site, and quick turn around on patches.

          Reply
          • Hello,

            I have patched manually the three files that are appointed in this patch, but I am not very skilled in applying patches with patch. So I decided to change the C files myself and insert the changes.

            It worked. These are two files inside the nvidia subdirectory and one file inside the nvidia-drm subdirectory. Just locate the appointed files and copy (with root privileges) – then go and upgrade the kernel.

            Everything should be located at /usr/src/nvidia-390.144/

            The files can be downloaded from this link:

            https://www.mediafire.com/folder/788f7sxpi1q6s/nvidia

            I hope this helps for now!
            Best regards.

            Reply
              • Hi JR!
                Ok, thanks!
                Just in case one does not want to mess with scripting and patching, and already has the proprietary driver framework under /usr/src, it’s just a matter to overwrite these files and the dkms will compile. It rests as another way to do it. I’m glad we’ve come up with these solutions very early (and not 6 months as another folk mentioned!).

                Cheers.

                — D. B.

                Reply
      • I see that Emanuele Rocca has done the entire receipt as where to patch, but it’s not automatized yet. I don’t want to mess with patch right now, but if anyone could drop some instructions here on getting that text on a diff and patch that group of files would be nice. Thanks for the info.

        Reply
    12. THANK YOU VERY MUCH! Everything works!

      nvidia-installer -v |grep version
      nvidia-installer: version 470.74

      uname -a
      Linux asus 5.14.9-200.fc34.x86_64 #1 SMP Thu Sep 30 11:55:35 UTC 2021 x86_64 x86_64 x86_64 GNU/Linux

      lspci |grep -E ‘VGA|3D’
      00:02.0 VGA compatible controller: Intel Corporation 4th Gen Core Processor Integrated Graphics Controller (rev 06)
      01:00.0 3D controller: NVIDIA Corporation GM107M [GeForce GTX 860M] (rev a2)

      echo $XDG_SESSION_TYPE
      wayland

      Reply
    13. Hi there, I’m using F34. I managed to install the driver successfully apparently, this is my output..
      lspci |grep -E “VGA|3D”
      00:02.0 VGA compatible controller: Intel Corporation 4th Gen Core Processor Integrated Graphics Controller (rev 06)
      01:00.0 3D controller: NVIDIA Corporation GM107M [GeForce GTX 950M] (rev a2)

      However when I go to settings->about, in graphics, the Intel card is still showing. do you know why is that?

      Reply
    14. Not working with Acer nitro 5 GeForce RTX 3050. Have tried both nivida 495 and 470. Get to installing driver it fails. Hard to read it it fails dkms.

      Reply
      • Hello Dave,

        Could you post exact error message?

        Reply
1 117 118 119 120

Leave a Reply to Suzanna Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Close