Fedora 35/34/33 NVIDIA [510.39.01 / 495.46 / 470.94 / 390.147 / 340.108] Drivers Install Guide - Comment Page: 121

This is guide, howto install NVIDIA proprietary drivers (manually using .run files) on Fedora 35/34/33/32/31 and disable Nouveau driver. This guide works with GeForce 8/9/200/300/400/500/600/700/800/900/10/20/30 series cards. GeForce RTX 30 series cards works with 510.xx, 495.xx, 470.xx, 465.xx and 460.xx NVIDIA drivers, (RTX 3090, RTX 3080 and RTX 3070, RTX 3060, RTX 3060 Ti) GeForce RTX 20 series cards works with 510.xx, 495.xx, 470.xx, 465.xx, 460.xx and 450.xx NVIDIA drivers (RTX 2080 Ti, RTX 2080, RTX 2070 Ti, RTX 2070, RTX 2060) GeForce GT/GTX 600/700/800/900/10 series cards works with 495.xx, 470.xx, 465.xx, 460.xx, 450.xx and 390.xx NVIDIA drivers (GTX 1080 Ti, GTX 1080,...

3,100 comments on “Fedora 35/34/33 NVIDIA [510.39.01 / 495.46 / 470.94 / 390.147 / 340.108] Drivers Install Guide - Comment Page: 121

1 119 120 121
    1. Success:
      Thank you for the detailed write up. I am not sure if the package from rpmfusion is wrong or broken (495.44 vs 495.46), but before finding this guide – I ran into issues where I would just get a black screen right before login on a fresh install of Fedora 35.

      nvidia-installer:
      version 495.46

      uname:
      Linux fedora 5.15.6-200.fc35.x86_64 #1 SMP Wed Dec 1 13:41:10 UTC 2021 x86_64 x86_64 x86_64 GNU/Linux

      lspci |grep -E “VGA|3D”:
      03:00.0 VGA compatible controller: NVIDIA Corporation GM204GL [Quadro M4000] (rev a1)
      04:00.0 VGA compatible controller: NVIDIA Corporation GM204GL [Quadro M4000] (rev a1)
      82:00.0 VGA compatible controller: NVIDIA Corporation GM204GL [Quadro M4000] (rev a1)

      Reply
    2. 390.147 is available from NV and I verified it doesn’t need a patch with 5.15 kernels

      Reply
      • 390.147 on kernel 5.15.10 gnome doesn’t start

        Reply
        • This of course depends on your system. Could you post output of following command:

          lspci |grep -E "VGA|3D"
          Reply
    3. Hello ! Thanks, nice tutorial !

      A question, maybe you know.. :

      How to get free from the ‘llvmpipe’ screwing Nvidia driver rendering ?

      =======================================================
      glmark2 2021.02
      =======================================================
      OpenGL Information
      GL_VENDOR: Mesa/X.org
      GL_RENDERER: llvmpipe (LLVM 13.0.0, 128 bits)

      Thank you :)

      Reply
      • Do you have NVIDIA drivers installed succesfully?

        Could you also post output of following command:

        lspci |grep -E "VGA|3D"
        
        Reply
    4. [[email protected] ~]$ nvidia-installer -v | grep version
      nvidia-installer: version 340.108 ([email protected])
      [[email protected] ~]$ uname -a
      Linux fedora 5.15.12-200.fc35.x86_64 #1 SMP Wed Dec 29 15:03:38 UTC 2021 x86_64 x86_64 x86_64 GNU/Linux
      [[email protected] ~]$ lspci | grep -E “VGA|3D”
      03:00.0 VGA compatible controller: NVIDIA Corporation GT218 [GeForce 8400 GS Rev. 3] (rev a2)
      08:01.0 VGA compatible controller: Matrox Electronics Systems Ltd. MGA G200eW WPCM450 (rev 0a)
      [[email protected] ~]$

      Reply
    5. Hi JR. I upgraded to 390.147 a few days ago, which worked for kernel-5.15.12 on Fedora 34. But after upgrading to kernel-5.15.13 this morning the reboot failed. (5.15.12 is still OK.) My VGA is GF116 [GeForce GTX 550 Ti] (rev a1). Should I wait to see if yet a more recent driver (> 390.147) appears? I always rely on your marvelous assistance! Thanks so much.

      Reply
    6. When i perform the steps in 4.2 and then run 4.3 i get the following errors

      libkmod: kmod_config_parse: /etc/modprobe.d/nvidia.conf line 1: ignoring bad line starting with ‘add_drivers+=”‘
      libkmod: kmod_config_parse: /etc/modprobe.d/nvidia.conf line 2: ignoring bad line starting with ‘install_items+=”‘

      what do I need to do to fix this.?

      Reply
      • Hi Steve,

        Looks like that you have add_drivers and install_items lines in /etc/modprobe.d/nvidia.conf ? Both should be in /etc/dracut.conf.d/nvidia.conf file.

        Reply
    7. OH. I tried again with 390.147 with (in run level 3) kernel-5.15.13, and this time it all worked fine. I have no idea what the problem was on January 11. Oh well.

      Reply
      • Hi Peter,

        This is weird. It sounds that dkms has failed to compile the driver for some reason. dkms build log might help to debug problem. Currently it’s clean, but if this happens again. Great to hear that everything works now.

        Reply
1 119 120 121

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Close